Viking error code · F2
Viking Range Code F2 (Oven Over-Temperature Lockout)
Viking oven code F2 means an over-temperature condition: the control read the cavity hotter than allowed and shut off heat. Often a stuck relay or sensor.
Viking oven code F2 is an over-temperature lockout: the electronic control read the oven cavity hotter than its safe limit and cut power to the heating elements. It commonly points to a welded bake-element relay, a failing temperature sensor, or a control that is not switching the element off.
F2, explained
F2 fires when the oven temperature sensor reports a reading above the control's hard ceiling, often during bake or self-clean. The control treats runaway heat as a safety event and locks out the oven so the element cannot keep firing. It tells you the cavity got too hot, not why, so the relay, sensor, and element circuit all have to be checked.
Severity:Service needed · Appliance:Range
Frequently asked
Viking F2 — questions
What does F2 mean on a Viking oven?
It is an over-temperature lockout. The control read the cavity hotter than its safe limit and cut power to the elements. The usual culprits are a stuck element relay or a temperature sensor reading too high.
Is it safe to keep using the oven with F2?
No. F2 can indicate an element is still heating after the control tried to shut it off, which is a genuine fire risk. Switch the oven off at the breaker and have it diagnosed before further use.
Can I fix a Viking F2 code myself?
No. F2 requires testing whether a relay welded closed or the sensor failed, both of which involve line voltage and resistance measurement. The repair is typically a control board or sensor replacement done by a technician.
How do I reset the F2 code?
Shut off the breaker for a couple of minutes and restore power. If a relay is welded or the sensor is bad, F2 will return, which confirms a hardware fault rather than a glitch.
Why did F2 appear during self-clean?
Self-clean drives the cavity to its highest temperatures, so a relay that is starting to weld or a sensor drifting high will trip the over-temp limit during that cycle more readily than during normal baking.
How long does an F2 repair take?
A diagnostic visit is a flat $89, and most F2 repairs, whether a control board or sensor, are completed in a single visit once the part is on hand. Every repair carries a 365-day warranty. Call (650) 668-1554.
Could F2 be just a calibration issue?
Sometimes the oven runs hot from calibration drift, but F2 is a hard lockout above the safety ceiling, so it points to a failed component rather than minor calibration and should be tested, not just recalibrated.
Why F2 appears
The most dangerous cause is a bake-element relay that has welded closed on the control board, so the element keeps heating after the control commands it off. A drifting or shorted temperature sensor can also report false high readings, and a wiring fault can keep an element energized. Self-clean's extreme heat frequently exposes a marginal relay.
How F2 shows up
- Oven displays F2 and shuts off mid-cycle
- Cavity is noticeably hotter than the set temperature
- Food burns or over-browns at normal settings before the code appears
- Code most often appears during bake or self-clean
- Element appears to stay glowing after the oven is turned off
What usually causes it
- Bake or broil element relay welded closed on the control board
- Failed or drifting oven temperature sensor (RTD) reading high
- Shorted sensor wiring giving a false over-temp signal
- Electronic oven control miscalibrated or unable to open the element circuit
- Stuck element circuit keeping power on the element
Which part F2 points to
- Electronic oven control (EOC) board — Replaced when a relay has welded closed and the control can no longer shut off the element
- Oven temperature sensor (RTD) — Replaced when the sensor reads high or its resistance is out of spec
- Bake or broil element — Replaced if the element is shorted to its circuit and stays energized
What you can safely check
- Turn the oven off at the breaker immediately and leave it off until inspected
- Note whether the cavity feels far hotter than the setpoint
- Confirm the model number so the exact F2 over-temp threshold can be verified
When F2 needs a technician
An over-temperature fault can mean an element is still being powered with the control off, which is a fire and burn hazard. Confirming a welded relay versus a bad sensor requires line-voltage testing and resistance checks that must be done by a technician, and a welded relay means the control board has to be replaced.
Got F2?
We'll pinpoint it and bring the right part. $89 diagnostic, 365-day warranty.
Book a technicianSubzero Repair · Open 24/7 · 365-day warranty
Need Viking repair in the Bay Area?
Call for urgent cooling or cooking failures, or book online for a service window across the Bay Area.