Thermador error code · E01
Thermador Dishwasher Error E01: Control Board / Electronic Fault
Thermador dishwasher E01 is an electronic control fault. Try a power-cycle reset first; a persistent E01 usually means the control board needs service.
Thermador dishwasher error E01 indicates an internal electronic control fault, where the main control board has detected a problem with itself, its memory, or a connected component. A power-cycle at the breaker sometimes clears a one-time glitch, but a persistent E01 usually means the control board needs to be tested and replaced.
What E01 means
E01 is a control-side fault on the Bosch-platform electronics. The main board runs self-checks on its processor, memory, relays, and the communication link to the control panel and power module; a failed check sets E01. Because the exact trigger varies by model and generation, E01 should be treated as a control-fault category and confirmed against the specific model before any board is replaced.
Severity:Service recommended · Appliance:Dishwasher
Why E01 happens
Power surges, brownouts, and lightning can corrupt the board's memory or damage its components. Moisture intrusion into the control housing, failed solder joints from heat cycling, a bad relay, or a broken ribbon/communication cable between the user panel and main board are common triggers. Age-related component failure on the power module also produces this fault.
Common causes
- Main control board / power module internal fault
- Corrupted control memory after a power surge or brownout
- Moisture intrusion into the control or door electronics
- Failed relay or solder joint on the board
- Broken communication cable between the user panel and main board
What you'll typically see
- E01 appears on the display, sometimes immediately at power-up
- Dishwasher will not start a cycle or stops shortly after starting
- Buttons or display unresponsive or behaving erratically
- Lights flash abnormally or the panel resets on its own
- Code returns after a power-cycle reset
Parts involved in E01
- Main control board / power module — Replace when self-checks fail and a reset does not clear the fault
- User interface / control panel — Replace if the panel side of the communication link is the source rather than the main board
- Inter-board communication cable — Replace if the ribbon or harness between panel and board is damaged
What you can check yourself
- Power the dishwasher off at the breaker for two to three minutes, then restore and retest (this clears one-time glitches)
- Confirm the unit is on a stable circuit and not sharing with a high-draw appliance causing brownouts
- Make sure the door closes and latches fully so the panel powers correctly
- Note whether E01 returns immediately or only intermittently and report the pattern
When to book a pro
Because E01 is a control-fault category that varies by model, a technician must confirm the exact meaning for your unit and test whether the main board, user panel, or wiring link is at fault before replacing the expensive control board. Guessing leads to unnecessary parts cost.
Have this code?
Send us the code and your model — flat $89 diagnostic, 365-day warranty.
Book a technicianFrequently asked
E01 FAQ
What does E01 mean on a Thermador dishwasher?
It indicates an internal electronic control fault: the main board failed a self-check or lost communication with the panel or power module. It is a control-side error rather than a wash or drain problem.
How do I reset the E01 code?
Turn the dishwasher off at the breaker for two to three minutes, then restore power and retest. A one-time glitch from a power blip will often clear. If E01 returns, the board likely needs service.
Can I fix E01 myself?
Only the reset step is an owner task. Diagnosing the board, panel, and communication cable requires meter testing and disassembly, so a persistent E01 is a technician repair.
Did a power surge cause E01?
Often, yes. Surges and brownouts can corrupt the control memory or damage the power module. Putting the dishwasher on a stable, surge-protected circuit helps prevent a repeat.
Is the exact cause of E01 the same on every Thermador?
No. The precise trigger for E01 varies by model and control generation, so the exact decode must be confirmed against your model and manual before a board is replaced.
Is it worth repairing the control board?
Usually yes on a built-in Thermador, since the rest of the machine is sound. Our diagnostic visit is a flat $89 and confirms whether it is the board, panel, or cable, with a 365-day warranty on the repair; call (650) 668-1554.
Subzero Repair · Open 24/7 · 365-day warranty
Need Thermador repair in the Bay Area?
Call for urgent cooling or cooking failures, or book online for a service window across the Bay Area.