GE Monogram error code · F0 / F1
GE Monogram Oven Codes F0 and F1: Electronic Control Failure
GE Monogram F0 or F1 signals an electronic oven control (ERC) failure - a stuck key or internal board fault. Usually the control board or touchpad.
GE Monogram oven codes F0 and F1 indicate an electronic oven control failure - the control board has detected an internal fault or a stuck/shorted key it cannot clear. The fix is usually replacing the electronic control board (ERC), and sometimes the touchpad.
What F0 / F1 means
F0 and F1 are control-failure codes. The electronic range control (ERC) - the board with the clock, keypad logic, and oven relays - runs self-checks. F0 and F1 are posted when it finds an internal failure or a continuously detected key, and the oven locks out. Because the exact decode of F0 versus F1 varies by Monogram model and control generation, the precise meaning must be confirmed against your model number and tech sheet; both point at the control or its keypad.
Severity:Service recommended · Appliance:Wall Oven
Common causes
- Failed electronic oven control board (ERC)
- Stuck or shorted touchpad key feeding a held signal to the board
- Power surge or brownout damage to the control
- Moisture or heat damage to board components or solder joints
- Corroded touchpad ribbon connection at the board
Why F0 / F1 happens
Control boards fail from heat aging of solder joints and relays mounted near the hot oven, from power surges, and from moisture creeping into the control housing. A stuck or shorted touchpad key can also drive an F0/F1 by feeding the board a signal it reads as a permanent command. On some generations these codes overlap with the stuck-key family, which is why model-specific confirmation matters.
What you'll typically see
- F0 or F1 on the display, often with a persistent tone
- Oven unresponsive to all button presses
- Display garbled, frozen, or cycling
- Code returns immediately after a power reset
- Clock keeps time but oven functions are locked out
Parts involved in F0 / F1
- Electronic oven control board (ERC) — Primary replacement when self-check fails or relays/logic are faulty
- Membrane touchpad / keypad — Replaced when a stuck key is driving the F0/F1 rather than the board
What you can check yourself
- Power the oven off at the breaker for 3-5 minutes, then restore power
- Confirm the exact code (F0 versus F1) and note it for the technician
- Record the full model number so the correct board generation is sourced
- Check for any visibly stuck or damaged button on the panel
When to book a pro
F0/F1 require reading the model-specific tech sheet to confirm the decode, then isolating the touchpad from the board and replacing the correct ERC - line-voltage work that also needs the proper board revision for your model.
Have this code?
Send us the code and your model — flat $89 diagnostic, 365-day warranty.
Book a technicianFrequently asked
F0 / F1 FAQ
What do F0 and F1 mean on a GE Monogram oven?
They signal an electronic oven control (ERC) failure - the board found an internal fault or a stuck key it cannot clear, and locks the oven out. The exact F0-versus-F1 decode depends on your model, but both point at the control board or touchpad.
Why can't you give one exact meaning for F0/F1?
GE has used several Monogram control generations, and the precise definition of F0 versus F1 differs between them. Rather than guess, a technician confirms it against your model number and tech sheet so the right part is replaced.
Will resetting power fix F0 or F1?
A breaker reset for several minutes occasionally clears a one-time glitch. If the code returns, the control board or touchpad has a real fault and needs replacement.
Is it the board or the touchpad?
Either can cause F0/F1. A stuck key can feed the board a permanent signal, so the technician isolates the touchpad first; if it tests good, the control board is replaced.
Is the oven safe to use with F0/F1 showing?
The oven has already locked itself out, so it will not cook. Leave it powered off until repaired - a faulty control should not be coaxed back into running.
How much does an F0/F1 control repair cost?
Cost depends on whether the board or touchpad is at fault and the board revision your model needs. Our diagnostic is a flat $89, applied to the repair, with a 365-day warranty. Call (650) 668-1554.
Subzero Repair · Open 24/7 · 365-day warranty
Need GE Monogram repair in the Bay Area?
Call for urgent cooling or cooking failures, or book online for a service window across the Bay Area.